How to Remove the Truck From Skateboard? (Easiest Methods)

How to Remove the Truck From Skateboard? (Easiest Methods)

A skateboard is a short board that typically measures 28-32 inches long and 7-10 inches wide. A truck is a metal frame that holds the wheels of a skateboard in place. Most skateboards have two trucks, one at the front and one at the back. Some people prefer to ride with only one truck for a variety of reasons. 

Trucks are one of the main parts of a skateboard, and they can be a pain to remove if you don’t know how. This article will show you how to remove trucks from skateboards in just a few easy steps. With these simple tips, you’ll be able to take your skateboard apart and put it back together in no time.

Why Remove Trucks From Skateboards?

There are a few reasons to remove trucks from a skateboard. The first is to clean them. Trucks can get very dirty, especially if they’re ridden in the street. They can also get rusty, so it’s important to keep them clean and dry. 

The second reason to remove trucks is to change their wheels. Skateboard wheels wear down over time and need to be replaced periodically. The third reason is to adjust the trucks’ height.

This can be done by loosening the nuts on the truck’s axle and raising or lowering the truck until it’s at the desired height. 

Finally, trucks may need to be removed for transportation purposes. If you’re taking your skateboard on a plane or train, for example, you’ll need to remove the trucks before packing it up.

How to Remove the Truck From Skateboard?

Here are a few ways to remove the truck from a skateboard:

1) Use A Screwdriver

There are a few different ways that you can remove trucks from your skateboard, and one of those is by using a screwdriver. This method is relatively simple and only requires that you have a screwdriver on hand. 

First, you’ll want to find the screws that are holding the truck in place. There are typically two of them, and they’re located on either side of the truck. Once you’ve found the screws, use your screwdriver to loosen and remove them. 

With the screws removed, the truck should come right off. If it’s still not coming off easily, you can try gently prying it with your screwdriver until it pops free.

The wheels of your skateboard can make a huge difference in your ride. A lot of people who don’t know where to put their wheels will have trouble getting them on right, and they will also be at risk of losing control when you’re riding at high speeds.

2) Use A Hammer

Hammer also helps you to remove skateboard trucks. You just need to Place the board on a solid surface, and then take a hammer and hit the kingpin in the middle of the truck. You should hear a popping sound as the truck comes off the board. Repeat this process for the other truck.

The second method is to have someone help you push the trucks off of the board. This is the best way to get it done if you don t have a hammer or if you’re just a little on the wimpy side.

Put the board on a solid surface and then have your buddy push down on the tail of the board while you push down on the nose of the deck. Once you get some momentum, push down as hard as you can and both trucks should pop right off.

The third method is to use pliers. Place the board on a solid surface, and then take a pair of pliers and grip them onto the hanger of the truck.

3) Use A Crowbar

When it comes to removing trucks from a skateboard, one of the best methods to use is a crowbar. This will help to pry the trucks off of the board without damaging the deck.

To begin, place the skateboard on a stable surface and insert the crowbar under one of the trucks. Next, apply pressure to the crowbar in order to pry the truck off of the board. You may need to use some force, but be careful not to damage the deck.

Remove Skateboard Truck using crowbar

Once you have removed one truck, repeat this process for the other truck. With both trucks removed, your skateboard is now ready for new trucks!

4) Use A Heat Gun 

A heat gun can be used to remove trucks from a skateboard. This method is effective because the heat can loosen the adhesive that is holding the trucks in place. It is important to be careful when using a heat gun, as too much heat can damage the skateboard deck.

To remove trucks with a heat gun, first set the heat gun to a low setting and hold it close to the truck base for a few minutes. This will soften the adhesive holding the truck in place.

Remove Skateboard Truck using heatgun

Once the adhesive is softened, you should be able to twist the truck off of the deck. If necessary, you can increase the heat of the gun and hold it on the truck for long periods of time.

What Are Some Of The Dangers Of Removing Trucks From A Skateboard?

There are a few dangers of removing trucks from a skateboard. First, if the trucks are not removed correctly, it can damage the skateboard deck. Second, without trucks, the skateboard will be less stable and more difficult to ride. Third, without trucks, the wheels will sit directly on the ground which can cause them to wear down quickly.

How Can I Find Out What Size Skateboard Trucks Will Fit On My Deck?

When you are looking to purchase new skateboard trucks, it is important to know what size will fit your deck. There are a few different ways that you can find out this information.

One way to determine the right size trucks for your deck is to look at the width of your deck. The width is measured from the inside of the truck’s axle to the inside of the other truck’s axle. Most decks are between 7.5 and 8 inches wide. If your deck is on the wider side, you will want to purchase trucks that are also on the wider side.

Another way to figure out what size trucks will fit your skateboard deck is by measuring the length of your board. You will want to measure from the tip of the nose to the tail and then subtract about an inch.

Conclusion:

As the debate continues about whether trucks should be removed from skateboards, it’s important to consider all sides of the argument. Some say that trucks are essential for stability and control, while others argue that they make the sport too dangerous. Ultimately, it’s up to each individual skater to decide what’s best for them.

There are a few things to keep in mind if you’re thinking about removing trucks from your skateboard. First, it will be harder to balance without trucks. Second, you’ll need to be more careful when landing tricks since you won’t have the same level of stability. And finally, you’ll need to put in extra effort to pump the board since truckless skateboards are harder to push.

If you’re still on the fence about whether or not to remove your trucks, consider giving it a try without them first.


Share post on


Boarding Vela is reader-supported. When you buy through links on our site, we may earn an affiliate commission.

Social Links

Can Skateboarding Cause Lower Back Pain BLOG

Can Skateboarding Cause Lower Back Pain

Skateboarding is a popular activity among adolescents and young adults, but it is also...

By Sammy Ekaran
What is The Difference Between A Pro Skateboard and A Beginner Skateboard? BLOG

What is The Difference Between A Pro Skateboard and A Beginner Skateboard?

When a person is first starting to skateboard, they may not know the difference...

By Sammy Ekaran
What to Do if Your Skateboard Turns its Own? BLOG

What to Do if Your Skateboard Turns its Own?

In the past decade, skateboards have been turning on their own, much to the...

By Sammy Ekaran
How To Remove The Wheel Locks On A Skateboard With A Drill? BLOG

How To Remove The Wheel Locks On A Skateboard With A Drill?

If you've ever been skateboarding, you know that one of the most annoying things...

By Sammy Ekaran
What Is Skateboarding Learning? BLOG

What Is Skateboarding Learning?

Skateboarding is a unique sport that can be enjoyed by people of all ages....

By Sammy Ekaran
How To Remove Stuck Bearings From Skateboard? BLOG

How To Remove Stuck Bearings From Skateboard?

If you're a skateboarder, you know that one of the most frustrating things that...

By Sammy Ekaran
How To Remove Rust From Skateboard Bearings? (Easy Methods) BLOG

How To Remove Rust From Skateboard Bearings? (Easy Methods)

If you are a skateboarder, you know how important it is to keep your...

By Sammy Ekaran
How To Remove Old Grip Tape From Skateboard? BLOG

How To Remove Old Grip Tape From Skateboard?

Grip tape is a vital part of any skateboard, providing much-needed traction between the...

By Sammy Ekaran

Latest Posts

Can Skateboarding Cause Lower Back Pain BLOG

Can Skateboarding Cause Lower Back Pain

Skateboarding is a popular activity among adolescents and young adults, but it is also...

By Sammy Ekaran
What is The Difference Between A Pro Skateboard and A Beginner Skateboard? BLOG

What is The Difference Between A Pro Skateboard and A Beginner Skateboard?

When a person is first starting to skateboard, they may not know the difference...

By Sammy Ekaran
What to Do if Your Skateboard Turns its Own? BLOG

What to Do if Your Skateboard Turns its Own?

In the past decade, skateboards have been turning on their own, much to the...

By Sammy Ekaran
How To Remove The Wheel Locks On A Skateboard With A Drill? BLOG

How To Remove The Wheel Locks On A Skateboard With A Drill?

If you've ever been skateboarding, you know that one of the most annoying things...

By Sammy Ekaran
What Is Skateboarding Learning? BLOG

What Is Skateboarding Learning?

Skateboarding is a unique sport that can be enjoyed by people of all ages....

By Sammy Ekaran
How To Remove Stuck Bearings From Skateboard? BLOG

How To Remove Stuck Bearings From Skateboard?

If you're a skateboarder, you know that one of the most frustrating things that...

By Sammy Ekaran
How To Remove Rust From Skateboard Bearings? (Easy Methods) BLOG

How To Remove Rust From Skateboard Bearings? (Easy Methods)

If you are a skateboarder, you know how important it is to keep your...

By Sammy Ekaran
How to Remove the Truck From Skateboard? (Easiest Methods) BLOG

How to Remove the Truck From Skateboard? (Easiest Methods)

A skateboard is a short board that typically measures 28-32 inches long and 7-10...

By Sammy Ekaran